Oct 31, 2020 Leave a message

Suggestions for the development of magnesia refractory raw materials-PUDA refractory material packing machine

Strengthen the construction of magnesite ore supply base to ensure the supply of high-quality raw materials

The magnesia refractory raw material industry is a typical resource-based industry. Since China's reform and opening up in the 1980s, due to the rapid increase in the demand for magnesia raw materials, the entry barriers for the processing of primary raw materials have been low, resulting in serious damage to the rational development of magnesite. Due to economic reasons, the price of magnesite super-grade ore is about 5 times that of the third-grade ore, leading to extensive mining and serious “rich mining and abandoning of poverty”. Many low-grade ores in China’s view are not used, resulting in resources of great waste. More serious is the stripping disorder. The author participated in the “point adjustment” of 12 key magnesite mines in Liaoning in 2005. It was estimated that the rock stripping debt was over 100 million tons at that time, and the situation has not fundamentally changed since then. Now it is too late to "remedy the situation", causing difficulties in mining high-quality ore. In recent years, special-grade mines in the original sense have been very rare. The shortage of primary mines and the declining quality of ore have caused the average Mgo mass fraction of magnesia to drop by more than 0.5%.

refractory

Therefore, in order to use limited resources rationally and effectively, it is necessary to earnestly implement the "Industry Development Guidance Catalog: ①Further integrate magnesite mines and old mines with an annual mining volume of more than 300,000 tons, implement large-scale mining and intensive management. ②Do a good job of existing mining areas Investigation, mining according to mining design, key mines to make up for the debts of rock stripping, and prolong the service life of mines. ③Promote beneficiation technology and comprehensively utilize medium and low-grade ores.

At present, relevant companies have gradually realized that only relying on raw ore to produce raw materials can no longer maintain the production of high-quality raw materials; only by beneficiating and purifying raw ore can high-quality primary raw materials be produced to ensure the normal production of raw materials. Following the successful start-up of the flotation system in the Haicheng Magnesium Mine General Plant for many years, Huayu Group and the joint venture Aoding Company have completed the flotation project, and other companies have also begun preparations. The flotation plant with an annual processing capacity of 3.5 million tons of ore is now under construction . At the same time, the comprehensive utilization of flotation tailings is also under study.

In the next three to five years, the promotion of magnesite flotation technology and the subsequent processing of high-purity Mg(OH)2 produced by Tibet's cryptocrystalline magnesia and Qinghai "Salt Lake Magnesium Extraction" will provide high-quality magnesia production in China Guarantee of raw material supply.

Produce high-quality light burned magnesia according to the needs of domestic and foreign markets

According to foreign exchange data, the current global annual consumption of light burned magnesia is about 10 million tons. China is the world's largest producer of light burned magnesia, with an annual output of 3.5 million to 4 million tons. Japan, the United States and other countries used light burned magnesia for sintered magnesia and the ratio of non-refractory materials was 80:20 in the 1990s, then gradually changed to 70:30, and now it is roughly 65:35. Its construction abroad The large-scale light-burning plant in China has a wide variety of products and a wide range of uses. Therefore, focus on the use and development of light burned magnesia, not only used in refractory materials, but also should vigorously cultivate new magnesite material industries such as magnesium chemical industry and magnesium building materials to adjust the structure of light burned magnesia products. Only large-scale light burned magnesia concentrated production should be established. Only by forming the scale effect on the base can there be reasonable investment, so that advanced roasting technology and kilns can be adopted to solve energy conservation and emission reduction from the source, develop a low-carbon economy, and CO2 recovery.

In order to produce high-purity magnesia in conjunction with the "two-step calcination" process in southern Liaoning, China not only uses traditional reverberatory furnace light burnt magnesite nuggets, but also introduces fine ore concentrates from light burnt magnesite flotation in foreign suspension furnaces. The magnesite crushed ore is lightly burned with rotary kiln, fluidized bed furnace, and new type of suspension furnace. The multi-layer furnace (MHK) of Aoding Company has been put into production, and the large-scale air flow suspension furnace and cement industrial kiln used for roasting Al(OH) in the non-ferrous metal industry External calcining furnaces provide favorable conditions for the selection of kilns for light burning magnesia.

Adjust the structure of sintered magnesia products and develop low-cost and high-grade magnesia

It is generally believed that the performance requirements for high-grade magnesia in the global high-end refractory market are: w(MgO)≥98%, bulk density≥3.40g·cm-3 (sintered magnesia) or ≥13.50 g·cm-3 (electrical Fused magnesia). The annual consumption of high-grade magnesia in high-temperature industrial sectors such as steel and cement is about 1 million tons.

The total annual output of sintered magnesia in China is about 4 million tons. Around 1980, the export volume of cheap natural magnesia from China soared, and it has always occupied the international low-end magnesia market. Generally speaking, the supply of middle and low-end magnesia exceeds demand in the market. The output of this part of sintered magnesia should be controlled, especially the production of re-burned magnesia should be gradually restricted. Due to declining ore grades and rising fuel and labor prices, the quality of mid-range magnesia and high-purity magnesia has declined significantly. In the future, the market demand for medium-grade magnesia and high-purity magnesia will increase. Therefore, it is obvious that medium-grade sand will replace heavy burned sand and high-purity sand will replace part of fused sand upward.

After more than 30 years of disorderly mining, it is an indisputable fact that China's high-quality magnesite ore has decreased and the quality of magnesia has declined. At present, relevant companies gradually realize the importance of ore flotation and purification, and it is an inevitable trend to promote beneficiation technology. From beneficiation personnel to improve the grade of ore, to produce high-activity light-burned magnesia with energy-saving and efficient light-burning equipment, and to improve the quality of high-purity sand through production methods such as dry high-pressure dry ball and clean fuel high-temperature calcination. It is also necessary to explore new magnesia production processes and new processes to produce high-grade sintered magnesia with a low cost of w(MgO)=98% and bulk density ≥3.40 g·cm-3.

The construction of a large-scale production plant integrating mineral processing and high-purity magnesia production is in line with the future development direction. Aoding's high-purity magnesia plant is a domestic demonstration plant for high-end products, but currently its magnesia with w(MgO)≥98% and bulk density 3.35~3.40 g·cm-3 is very expensive, and it is not yet domestic refractory Accepted by product manufacturers.

Restrict development and improve the production technology and equipment of fused magnesia

Due to the extremely competitive price of China's fused magnesia, a large number of western seawater magnesia manufacturers have closed down. At present, in the world market of fused magnesia with w(MgO)>98.5%, China occupies 90% of it, and its applications are more extensive. However, the product consumes high energy and requires superior raw materials. Therefore, the comprehensive promotion of improved technical equipment measures in the fused magnesia industry will help reduce energy consumption and control quality. This is an inevitable trend for future development.

Focus on the development of magnesium synthetic raw materials

At present, the synthetic raw materials based on magnesia in Liaoning, China mainly include fused magnesia chrome sand, sintered magnesia calcium sand, sintered magnesia alumina spinel sand, sintered magnesia alumina iron sand, etc. The annual output exceeds 200,000 tons. Magnesia-calcium refractories have excellent performance, but due to the hydration problem of CaO, their application is limited. Therefore, the water-proof problem of magnesia-calcium refractories should be studied. It should be pointed out that because of the presence of free CaO, magnesium-calcium refractories have the effect of removing sulfur and phosphorus impurities in steelmaking; while the existence of free CaO, non-hydration is impossible, only to prevent its hydration.

With the increase in environmental protection, chromium-containing refractories will be withdrawn from the market, and the research and production of alternative products is imperative. Further development and production of MgO-Al2O3, MgO-CaO, MgO-ZrO2, MgO-SiO2 should be made for different purposes. , MgO-Fe2O3, MgO-CaO-Fe2O3, MgO-Al2O3-ZrO2, MgO-CaO-ZrO2, MgO-Al2O3-Fe2O3 (FeO) and other high-quality magnesium synthetic raw materials.


PUDA refractory material packing machine:

We recommend valve bag  impeller bagging machine, valve bag air bagging machine, mobile bagging machine, batching and weighing system in accord with various features of refractory materials and customers’ requirement, like packing speed, packing weight and the type of bags etc.


Send Inquiry

whatsapp

Phone

E-mail

Inquiry