Sep 18, 2020 Leave a message

These core technologies of silica powder

Silicon micropowder is an amorphous fine particle that is taken out of the furnace by the flue gas during the smelting of ferrosilicon and metallic silicon. Its main component is SiO2 and has excellent pozzolanic properties. With the gradual implementation of the national environmental protection law, the improvement of people's awareness of environmental protection and the increasing expansion of the application field of silicon powder, silicon-based ferroalloy manufacturers have successively built or upgraded flue gas purification systems, that is, silicon powder production systems. Recycling silicon powder, as far as possible to make waste resources and harmless, reduce the impact of industrial production on humans and the environment, not only economic benefits, but also social and environmental benefits.

微信图片_20200918161745

1 Introduction

Most of the existing electric furnaces for ferrosilicon production in China do not have facilities for recycling silicon powder, causing serious pollution. According to incomplete statistics, there are basically no silicon powder recovery facilities for ferrosilicon electric furnaces below 5MVA; only about 20% of 5~9MVA ferrosilicon electric furnaces have silicon powder recovery facilities, and large and medium-sized ferrosilicon electric furnaces above 9MVA have only 40%. There are silicon powder recycling facilities on the left and right. In the existing silicon micropowder recycling facilities, there are only a few that have passed technology, high degree of automation, and good results. As far as the author knows, some ferrosilicon manufacturers are still choosing dust removal facilities that have proved to be unsuitable for the purification of flue gas from ferrosilicon electric furnaces. Tengda Northwest Ferroalloy Co., Ltd., an attempter of the use of bag filters for purifying flue gas from ferrosilicon electric furnaces in my country, and a beneficiary of surface filtration technology, now give an introduction on the application of silicon micropowder product production systems for reference.

2. Production of silicon powder

2.1 Silicon micropowder recycling and encryption process

The dust-containing flue gas generated during the smelting of the electric furnace is led to the air cooler by the low hood through the air duct and the flue gas of the tap hole. The cooler cools the flue gas temperature and then enters the cyclone dust collector to remove the large particles of dust and carbon particles in the flue gas, and then enters the bag filter to filter. The filtered flue gas is discharged from the chimney or the exhaust chamber at the top of the dust collector.

Most of the domestic dust collectors for recycling silicon powder are bag filters, both positive pressure and negative pressure; there are back-blowing internal filtration, and pulse injection external filtration; both use coated glass fiber filter materials, There are also flumes, glass fibers, 729 filter materials and so on.

The densification of microsilica powder is a condensation process that takes place in a silo and uses air from a blower as an energy source. The bulk density of silica powder can be controlled within 0.2~0.6t/m3. There are many factors that affect the entire encryption process, such as the moisture, fluidity, original bulk density, and operation of the silicon powder.

2.2 Recycling and encryption process of silicon powder

At present, the production of silicon powder is divided into 5 systems: C-1 system, C-2 system, C-3 system, Q-1 system, Q-2 system.

The C-1 system processes the flue gas from the 4×12.5MVA ferrosilicon electric furnace of the second smelter. It is divided into two sub-systems and is led out from the emission chimney, and sent to the C-1 baghouse dust collector through the air cooler, spark trap, and induced draft fan for purification. After the flue gas is discharged from the top of the dust collector.

The C-2 system processes the flue gas from the 2×25MVA ferrosilicon electric furnace of the third smelter. It is divided into two sub-systems and is led out from the venting chimney. The two sub-systems enter the C-2 baghouse dust collector through the air cooler and the spark trap. The induced draft fan is exhausted and discharged from the chimney.

The C-3 system processes the flue gas of a 7×5MVA electric furnace in a smelter. It is divided into two sub-systems and is led out from the emission chimney, and sent to the C-3 baghouse dust collector through the air cooler, spark trap, and induced draft fan. The purified smoke The air is discharged from the top of the dust collector.

The silicon micropowder collected by the Q-1 system and the C-2 system enters the encrypted and mechanized packaging.

The Q-2 system encrypts and mechanizes the silicon powder collected by the C-3 system.

The baghouse dust collectors of C-1 and C-2 systems are equipped with Gore-TEX membrane filter bags, and the baghouse dust collectors of C-3 system are equipped with domestic 729 filter bags. As far as the filter material is concerned, the technical and economic comparison between the company's use of glass fiber and film-coated glass fiber filter material is shown in Table 1.

Table 1 Technical and economic comparison of different filter materials used in ferrosilicon electric furnace

微信图片_20200918161926

It can be seen from Table 1 that after the ferrosilicon electric furnace adopts the coated glass fiber filter material, the technical and economic indicators of the dust collector are far superior to the ordinary glass fiber filter material.


3. The quality of silicon powder

The quality of silicon powder is mainly judged by the level of SiO2 content. The SiO2 content is less than 88%, and there is almost no market. The SiO2 content is 88% to 92%, which is mainly used in concrete, while the SiO2 content is greater than 92%, which is mainly used in refractory materials and other industries.

There is a difference in the quality of the recovered silicon powder in smelting metallic silicon and different grades of ferrosilicon; smelting the same grade of ferrosilicon, the quality of silicon powder will increase correspondingly with the increase of electric furnace capacity.

According to reports, silicon powder products with high SiO2 content and low alkali metals, alkaline earth metals and SO3 content have good fluidity and do not have an extreme effect on the curing time of castables, so they are easy to be adopted in the refractory industry.

3.1 Density of silica powder

Silicon powder is a by-product of smelting ferrosilicon or metallic silicon. Although it is widely used, it is still a low-value primary raw material. Unencrypted silicon powder has a density of 150~200kg/m3 and is called raw ash. Due to the low density of the original ash, it brings a series of problems to the packaging and transportation of the product. The manufacturer considers the profit, and the user must make the request according to the need. Therefore, the encrypted packaging of silicon powder has been adopted by many silicon powder companies. According to the specific domestic situation, the main purpose of the production enterprise for the encryption of silicon powder is:

(1) Reduce the packaging cost of silica powder;

(2) Reduce the transportation cost of silica powder;

(3) Increase the market share of silicon powder;

(4) Meet the various needs of users of silica powder, especially the requirements for fluidity;

(5) Improve the production environment of silicon powder.

According to the requirements of users, the company's product density can be arbitrarily selected within the range of 300~600kg/m3. At present, it mainly produces products with densities greater than 500kg/m3 and 300~350kg/m3.

3.2 Chemical composition of silicon powder

Due to the influence of many factors, the chemical composition of the silicon powder products produced by different silicon powder companies is quite different. Table 3 lists the chemical composition of several silicon powder products.

Table 3 The chemical composition% of several micro-silica products

微信图片_20200918161935

Send Inquiry

whatsapp

Phone

E-mail

Inquiry